3D Name Sign Generator
A name sign is the nursery-door, above-the-bed, behind-the-cake kind of print. Type the name in a script font and the letters connect into a single solid you can print flat and hang the same evening — no assembling individual letters, no glue-up. Designing and previewing is free.
Design your name sign
Starts on Pacifico with no base, because a wall sign wants the letters alone. Dancing Script and Corinthia give a finer, more formal line; switch to Anton if you want something bold and modern instead.
How big should a name sign be?
Signs are read across a room, so they run considerably larger than plates or tags. Sizes below are total width — most beds cap out around 250 mm, and longer signs need splitting.
150–200 mm
Nursery door
Sits above or beside the handle. Fits any common bed in one piece.
250–400 mm
Above the cot or bed
The classic wall piece. Past 250 mm you will need to split it — see below.
100–150 mm
Shelf or nook
Small enough to lean rather than hang. Add a base if you want it freestanding.
400 mm+
Party backdrop
Printed in sections and joined. Worth doing in one colour so the seams disappear.
Slicer settings for signs
Script letters are the fussiest thing this generator makes — thin strokes, long unsupported spans, lots of first-layer perimeter. These settings are tuned for that.
Layer height
0.12–0.16 mm
Script curves show stair-stepping badly at 0.2 mm. The extra time is worth it on a piece that hangs at eye level.
Wall loops
3–4
Thin strokes are almost entirely perimeter. More loops here is what actually makes the sign strong.
Brim
5 mm
The one setting people skip and regret. A long script sign has very little bed contact per letter and will lift at the ends without it.
Print time
2–4 hours
For a 200 mm nursery sign at 8 mm thick — roughly 30–45 g of filament.
Why script fonts and not block letters
In a script face the letters physically touch, so the whole name prints as one connected object. With a block font like Anton the letters are separate islands — you get eight loose pieces off the bed and have to align and glue them yourself. If you want a block-letter sign, keep the base on so the letters share a backing plate and stay in register.
Splitting a sign that is wider than the bed
Rotate the model 45° on the plate first — a 256 mm bed takes about 340 mm diagonally, which covers most names. If it still does not fit, cut it in your slicer at a point where the script naturally narrows, print the halves, and join them with superglue and a short length of 1.75 mm filament pushed through as an alignment pin. The seam disappears on a curve; it shows on a straight stroke, so choose the cut point carefully.
Hanging it without damaging the wall
A 200 mm PLA sign weighs 30–45 g, which is well inside what removable adhesive strips hold. Two strips at the extremes of the name, not one in the middle, or it will rotate. For something heavier or permanent, glue a keyhole hanger to the back — but print a small flat pad onto the back first in your slicer, because a curved script stroke gives the hanger nothing to bond to.
Colour and finish
Matte filament photographs far better than glossy for wall pieces and hides layer lines on curves. If you want a painted finish, print in any colour, hit it with a filler primer, and sand at 400 grit — script strokes are narrow enough that sanding a whole sign takes about ten minutes. Skip the primer and paint sits in the layer lines instead of covering them.
Name sign questions
Will the letters be connected or separate?
In a script font like Pacifico, Dancing Script or Corinthia they connect into one solid piece. In a block font they are separate unless you turn the base on, which joins them to a shared backing plate.
How do I make a sign wider than my print bed?
Rotate it diagonally on the plate first, which gets most names to fit. Beyond that, cut it in your slicer where the script narrows and glue the halves with a filament pin for alignment.
Is it strong enough to hang?
At 8 mm thick with three or four wall loops, yes. The failure point on thin script signs is nearly always a weak layer bond from printing too fast or too cool, not the design.
Can I make one for a nursery in a specific colour?
The colour you pick in the preview is just for the preview — the STL has no colour. Print it in whatever filament you want, or paint it after printing.
Is it free?
Designing and previewing is free with no account. You pay when you download the STL.
Can I get one printed if I don't own a printer?
Yes — download the STL and send it to a print service. Our 3D printed names page covers how that works.